• 怎么知道激光加工切割的速率?
  • 本站编辑:杭州创莘金属制品有限公司发布日期:2020-10-12 09:17 浏览次数:

激光加工切割速率影响创口总宽和创口粗糙度。不一样原材料的厚度,不一样的激光切割空气压力,激光切割速率有一个佳值,这一佳值约为很大激光切割速率的80%。激光切割速率假如太快得话,合理的光点面马上会缩小,这是由于速率过快造成 机器设备和原材料相互作用力的時间减短。那麼,光纤激光切割的特性对激光切割的速率有什么规定呢,下边苏州激光加工切割为大家做下详细介绍。

The cutting rate of laser processing affects the total width and roughness of the wound. Different thickness of raw materials, different laser cutting air pressure, laser cutting rate has a good value, which is about 80% of the large laser cutting rate. If the laser cutting rate is too fast, the reasonable light spot surface will be reduced immediately, which is due to the reduction of the interaction time between the machine equipment and raw materials due to too fast speed. So, the characteristics of fiber laser cutting on the speed of laser cutting, the following Suzhou laser processing and cutting for you to do a detailed introduction.

2-1F623102311.jpg

假如激光加工切割机的激光切割速率太快,会造成 创口的总宽缩小,因而光线的直射点马上会挨近,创口还会继续有拖线,创口的不光滑水平马上会增大还会继续有刮渣的状况。如果激光切割的速率太低,那激光器和原材料她们作用的時间马上会拉长,他的作用光点总面积也会增大,创口的总宽也会增大。激光加工切割速率不如溶化的速率,剩下的反应热让创口开展过多的溶化,这对热影响的范畴是比较大的。

If the laser cutting speed of the laser cutting machine is too fast, the total width of the wound will be reduced, so the direct point of the light will be close immediately, the wound will continue to have drag line, the unsmooth level of the wound will increase immediately, and there will continue to be scraping slag. If the cutting speed of laser is too low, the time of laser and raw materials will be lengthened immediately, the total area of light spot and the total width of wound will be increased. The cutting rate of laser processing is not as good as the melting rate, and the remaining reaction heat makes the wound melt too much, which has a great influence on the thermal field.

即然激光加工切割机的速率队激光切割特性有这么大的知名度,那麼我们该怎么知道光纤激光切割的速率呢?因为激光切割服务平台较短,用双眼没办法分辨是不是做到高速运行,我们可运用自动切割机的伺服控制器配用的手机软件仿真模拟作用来查询电动机的转速比是不是做到高。在检测激光加工切割切速时无需实切,提升交互速率。各轴可分离检测,也可另外检测。

That is to say, the speed of laser cutting machine is so well known for its laser cutting characteristics, then how can we know the cutting speed of fiber laser? Because the laser cutting service platform is short, it is impossible to distinguish whether the high-speed operation is achieved with both eyes. We can use the mobile phone software simulation function of the servo controller of the automatic cutting machine to check whether the speed ratio of the motor is high. When the cutting speed is increased, there is no need to detect the cutting speed interactively. Each axis can be tested separately or separately.


返回顶部